Skip to content

Furnace Control Board Repair in Austin, TX

The control board runs every step of a furnace cycle. When it fails, the furnace can go dead, light and shut off, or run the blower nonstop. We read the codes and test before we replace anything.

4.8 on Google from 400+ reviewsOpen Mon to Sat, 7am to 7pm✓ BBB A+ Rated✓ Nextdoor Neighborhood Favorite✓ Licensed & Insured

An open HVAC cabinet exposes a large blower wheel, copper tubing, electrical controls, and red and blue service gauge hoses.

Furnace Control Board Repair in Austin: The Furnace's Brain

Every modern gas furnace has a control board, a circuit board inside the cabinet that runs the heating cycle in order. It starts the inducer motor, waits for the pressure switch, heats the ignitor, opens the gas valve, watches the flame sensor and then runs the blower. If any step fails, the board shuts the furnace down and flashes a code on a small light.

Because the board touches every step, a furnace problem often looks like a board problem when it is really a worn ignitor, a dirty flame sensor or a stuck pressure switch. Gold Eagle Services reads the code, tests the parts the board is reporting on, and replaces the board only when the board itself has failed.

Gold Eagle Services HVAC installer loading an air handler

Signs of a Control Board Problem

A board problem can show up as:

  • No heat, with no lights or no response from the furnace
  • A blinking or steady error code on the board light
  • The blower running nonstop, or never starting
  • The furnace starting and stopping on its own
  • The AC and heat both acting up, since the board also runs the blower in cooling
  • Burn marks, a melted spot or a buzzing relay on the board
  • The furnace dying after a storm or a power surge

Write down the blink pattern before you turn the power off. It is the first clue we use, and it clears when the power is cut.

Schedule Online

Why Boards Fail

Control boards wear out like any electronics, and Austin attics are hard on them. Summer attic heat, power surges from storms, a shorted wire from a failing part, or condensate dripping onto the board from a clogged drain can all damage it. A low-voltage short, such as a nicked thermostat wire, can also blow the small fuse on the board and make the furnace look dead when the board is fine.

Many boards fail because of something else, so replacing a board without finding the cause can mean replacing it again. We check the wiring, the transformer, the fuse and the parts the board controls before we call the board bad.

Two Gold Eagle Services technicians handle tools beside an open service truck, with a coiled copper-colored line and gear visible.

What a Control Board Visit Includes

On a control board call we:

  • Read the blink code and check it against the furnace's chart
  • Check the low-voltage fuse, transformer and thermostat wiring
  • Test the inducer, pressure switch, ignitor, flame sensor and limit switch
  • Check the board's relays and outputs with a meter
  • Look for the cause: water, heat damage or a shorted part
  • Explain what failed, your options and the cost before any work starts

If the board needs replacing, we match it to your furnace’s model, set it up for your blower speeds and thermostat, and run the furnace through a full heating cycle and a cooling cycle before we leave.

Call 512-489-4653

Repair or Replace the Furnace?

A new control board brings most furnaces back to normal. If the furnace is older, has other worn parts, or the board for your model is hard to get, it can make more sense to replace the furnace. We lay out both options plainly. See furnace replacement, or price equipment with Build Your System.

If your home runs on a heat pump, the board in the air handler and the defrost board in the outdoor unit can fail too. Our heat pump repair team handles those. We offer a lifetime warranty on repairs with an ongoing maintenance agreement.

Frequently Asked Questions

It runs the heating cycle in order: inducer, pressure switch, ignitor, gas valve, flame sensor and blower. It also runs the blower when the AC is cooling, and it shuts the furnace down and flashes a code if a step fails.

Furnace blinking a code and blowing cold? Let us take a look.

Schedule Online

Need Help With Your HVAC? Let's Talk.

Tell us what you need, and our team will get back to you as soon as possible. No pressure, no obligation. Just honest advice and fast service.

Contact Us
This field is for validation purposes and should be left unchanged.
Name(Required)
Same-day service
BookTextCall 512-489-4653Call